Konfigurasi Static Router di Packet Tracer

10 comments 3131 views

Setelah kemaren nulis  installasi dan tingkat-tingkat akses sekarang nulis konfigurasi 4 router di koneksikan 4 pc yang subnetnya berbeda, kalau masih belum jelas tentang subnet bisa di baca pada artiket sebelumnya karena sebelum konfigurasi router harus bisa subnet terlebih dahulu.

berikut gambar desain jaringan yang akan di bahas

untuk pertama kalinya kita konfigurasi semua routernya, masalah ip addressnya bisa di lihat di konfigurasinya, berikut konfigurasi routernya

  • konfigurasi fa 0/0 , serial 0/0/1 dan serial 0/0/0 pada router fazza_router0
Router>enable
Router#configure
Configuring from terminal, memory, or network [terminal]?
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#hostname fazza_Router0
fazza_Router0(config)#interface fastEthernet 0/0
fazza_Router0(config-if)#ip address 192.168.1.1 255.255.255.0
fazza_Router0(config-if)#no shutdown
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
fazza_Router0(config-if)#exit
fazza_Router0(config)#interface serial 0/0/0
fazza_Router0(config-if)#ip address 10.10.10.1 255.255.255.252
fazza_Router0(config-if)#clock rate 64000
fazza_Router0(config-if)#no shutdown
%LINK-5-CHANGED: Interface Serial0/0/0, changed state to down
fazza_Router0(config-if)#exit
fazza_Router0(config)#interface serial 0/0/1
fazza_Router0(config-if)#ip address 10.10.40.2 255.255.255.252
fazza_Router0(config-if)#clock rate 64000
fazza_Router0(config-if)#no shutdown
%LINK-5-CHANGED: Interface Serial0/0/1, changed state to down
fazza_Router0(config-if)#exit
fazza_Router0(config)#
%LINK-5-CHANGED: Interface Serial0/0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0/0, changed state to up
fazza_Router0(config)#ip route 192.168.2.0 255.255.255.0 10.10.10.2
fazza_Router0(config)#ip route 192.168.3.0 255.255.255.0 10.10.40.1
fazza_Router0(config)#
  • konfigurasi serial 0/0/0 , serial 0/0/1 , fa 0/0 fa 0/1 pada router  fazza_router1
Router>enable
Router#configure
Configuring from terminal, memory, or network [terminal]?
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#hostname fazza_Router1
fazza_Router1(config)#interface fastEthernet 0/1
fazza_Router1(config-if)#ip address 192.168.2.1 255.255.255.0
fazza_Router1(config-if)#no shutdown
fazza_Router1(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/1, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up
fazza_Router1(config-if)#exit
fazza_Router1(config)#interface serial 0/0/0
fazza_Router1(config-if)#ip address 10.10.10.2 255.255.255.252
fazza_Router1(config-if)#clock rate 64000
fazza_Router1(config-if)#no shutdown
%LINK-5-CHANGED: Interface Serial0/0/0, changed state to up
fazza_Router1(config-if)#exit
fazza_Router1(config)#i
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0/0, changed state to u
fazza_Router1(config)#interface serial 0/0/1
fazza_Router1(config-if)#ip address 10.10.20.1 255.255.255.252
fazza_Router1(config-if)#clock rate 64000
fazza_Router1(config-if)#no shutdown
%LINK-5-CHANGED: Interface Serial0/0/1, changed state to down
fazza_Router1(config-if)#exit
fazza_Router1(config)#interface fastEthernet 0/0
fazza_Router1(config-if)#ip address 10.10.50.2 255.255.255.252
fazza_Router1(config-if)#no shutdown
fazza_Router1(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
fazza_Router1(config-if)#exit
fazza_Router1(config)#
%LINK-5-CHANGED: Interface Serial0/0/1, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0/1, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
fazza_Router1(config)#ip route 192.168.1.0 255.255.255.0 10.10.10.1
fazza_Router1(config)#ip route 192.168.3.0 255.255.255.0 10.10.50.1
fazza_Router1(config)#ip route 192.168.4.0 255.255.255.0 10.10.20.2
fazza_Router1(config)#
  • konfigurasi fa 0/0 , fa 0/1, serial 0/0/0 dan serial 0/0/1 pada router fazza_router2
Router#configure
Configuring from terminal, memory, or network [terminal]?
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#hostname fazza_Router2
fazza_Router2(config)#interface fastEthernet 0/0
fazza_Router2(config-if)#ip address 10.10.50.1 255.255.255.252
fazza_Router2(config-if)#no shutdown
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
fazza_Router2(config-if)#exit
fazza_Router2(config)#interface fastEthernet 0/1
fazza_Router2(config-if)#ip address 192.168.3.1 255.255.255.0
fazza_Router2(config-if)#no shutdown
%LINK-5-CHANGED: Interface FastEthernet0/1, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up
fazza_Router2(config-if)#exit
fazza_Router2(config)#interface serial 0/0/0
fazza_Router2(config-if)#ip address 10.10.30.2 255.255.255.252
fazza_Router2(config-if)#clock rate 64000
fazza_Router2(config-if)#no shutdown
fazza_Router2(config-if)#
%LINK-5-CHANGED: Interface Serial0/0/0, changed state to upe
% Ambiguous command: "e"
fazza_Router2(config-if)#exit
fazza_Router2(config)#
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0/0, changed state to up
fazza_Router2(config)#interface serial 0/0/1
fazza_Router2(config-if)#ip address 10.10.40.1 255.255.255.252
fazza_Router2(config-if)#clock rate 64000
fazza_Router2(config-if)#no shutdown
%LINK-5-CHANGED: Interface Serial0/0/1, changed state to up
fazza_Router2(config-if)#exit
fazza_Router2(config)#
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0/1, changed state to up
fazza_Router2(config)#ip route 192.168.1.0 255.255.255.0 10.10.40.2
fazza_Router2(config)#ip route 192.168.2.0 255.255.255.0 10.10.50.2
fazza_Router2(config)#ip route 192.168.4.0 255.255.255.0 10.10.30.1
fazza_Router2(config)#
  • konfigurasi fa 0/0,serial 0/0/0 dan serial 0/0/1 pada router fazza_router3
Router>enable
Router#configure
Configuring from terminal, memory, or network [terminal]?
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#hostname fazza_Router3
fazza_Router3(config)#interface fastEthernet 0/0
fazza_Router3(config-if)#ip address 192.168.4.1 255.255.255.0
fazza_Router3(config-if)#no shutdown
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
fazza_Router3(config-if)#exit
fazza_Router3(config)#interface serial 0/0/0
fazza_Router3(config-if)#ip address 10.10.20.2 255.255.255.252
fazza_Router3(config-if)#clock rate 64000
fazza_Router3(config-if)#no shutdown
%LINK-5-CHANGED: Interface Serial0/0/0, changed state to up
fazza_Router3(config-if)#exit
fazza_Router3(config)#interface
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0/0, changed state to up
% Incomplete command.
fazza_Router3(config)#interface serial 0/0/1
fazza_Router3(config-if)#ip address 10.10.30.1 255.255.255.252
fazza_Router3(config-if)#clock rate 64000
fazza_Router3(config-if)#no shutdown
%LINK-5-CHANGED: Interface Serial0/0/1, changed state to down
fazza_Router3(config-if)#exit
fazza_Router3(config)#
%LINK-5-CHANGED: Interface Serial0/0/1, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0/1, changed state to up
fazza_Router3(config)#ip route 192.168.2.0 255.255.255.0 10.10.20.1
fazza_Router3(config)#ip route 192.168.3.0 255.255.255.0 10.10.30.2
fazza_Router3(config)#
NB : untuk perintah menetapkan ip static (atau perintah ip route ) setelah konfigurasi ip router selesai semua
selajutnya seting PC, yang pertama pada fazza_PC0 buka DOS jalankan perintah berikut
ipconfig 192.168.1.2 255.255.255.0 192.169.1.1
keterangan :
ifconfig untuk memberi ip
192.168.1.2 ip yang dimiliki PC
255.255.255.0 networkmask
192.169.1.1  gateway
berikutnya konfigurasi fazza_PC1, jalankan perintah
ipconfig 192.168.2.2 255.255.255.0 192.169.2.1
selanjutnya konfigurasi fazza_PC2, jalankan perintah
ipconfig 192.168.3.2 255.255.255.0 192.169.3.1
berikutnya konfigurasi fazza_PC3, jalankan perintah
ipconfig 192.168.4.2 255.255.255.0 192.169.4.1
berikut contoh gambar konfigurasi dan hasil tes koneksi dengan perintah ping
okey cukup sekian dukumentasi kali ini.....
author
Linuxer | Blogger | Pencinta Kuliner | Suka Jalan2 | Pecandu sosial media
  1. author

    lukmanelhakimy7 years ago

    boss…
    thank u banget ne.. udah sangat ngbantu ogut

    Reply
    • author

      fazza017 years ago

      ok semoga bermanfaat

      Reply
  2. author

    dexrat6 years ago

    gmn caranya ngasi kabel dari router 0 ke router 1 ??
    koq aq coba cuma muncul console ja y…
    mohon bantuannya…
    thx b4…

    Reply
    • author

      fazza6 years ago

      pakai yang otomatis aja..

      Reply
  3. author

    AntoOneFinger6 years ago

    mas kalau cloud itu maksud'a apa???
    maklum masih belajar …

    Reply
    • author

      fazza6 years ago

      maksudnya cloud itu apa mas ?

      Reply
  4. author

    sugiono6 years ago

    masih mas ini sangat membantu

    Reply
  5. author

    Andhika5 years ago

    Mas….Kenapa ya…Saya Mengikuti Konfigurasi Anda…Dari Awal Sampai akhir tlah saya lakukan…& Semua Berhasil….Tapi pas Saya Ingin Ngeping ke Komputer 192.168.2.2 ko Muncul Pesan Bgini Ya…Destination Host Unreachable…& Saya Ingin Nge Ping dari Komputer 192.168.1.2 ke alamat Router 192.168.3.1 juga Pesan'a Demikian…Jadi Hanya Bisa Ngeping Komputer dngan Router'a ajj…192.168.1.2 Ping ke 192.168.1.1 ( Computer – Router )…Tolong Bantu Saya ya Mas…

    Trima Kasih Mas atas Tutorial'a

    Reply
    • author
      Author

      fazza5 years ago

      silahkan di cek kembali kabel yang di hubungkan cross atau strek
      cek pcnya menerima port apa aja
      semoga membantu

      Reply

Leave a reply "Konfigurasi Static Router di Packet Tracer"

______Anti Spam____ * Time limit is exhausted. Please reload CAPTCHA.